OLI NATURA® Wood Maintenance Oil - re-impregnate and refresh oiled wood
Oiled wood needs fresh oil from time to time, especially in areas where the surface is subject to daily wear. OLI NATURA® Wood Maintenance Oil complements the existing oil treatment, re-impregnates worn areas and renews the water- and dirt-repellent protection.
At the same time, the pigment-free maintenance oil made from natural oils revives the natural wood color, deepens it and accentuates the grain. For initial care and regular refreshing of oxidatively oiled parquet and plank floors, stairs and indoor furniture.
How can oiled wood be re-oiled?
Apply the ready-to-use wood maintenance oil in a thin layer using a cotton cloth, white polishing pad, sprayer or floor mop, work it in and completely remove excess oil within 10 minutes. Then buff dry. One liter covers approx. 50–100 m².
When do parquet floors, stairs and furniture need maintenance?
When water repellency diminishes, the wood color fades, or the surface looks dry and dull. Depending on use and wear, the wood maintenance oil can be applied over the entire surface or targeted at worn areas.
Wood maintenance oil or refresher - which maintenance oil is right?
OLI NATURA® Wood Maintenance Oil revives the natural wood color, deepens it and accentuates the grain.
OLI NATURA® Refresher cares for wood without visibly changing its appearance and preserves the existing color character without significantly deepening it. Particularly suitable for light-colored, white-oiled and raw-wood-look surfaces.
The wood maintenance oil is also available in the OLI NATURA® Care Set No. 1 and as a convenient sample size.
- GISCODE Ö60+
- DIBt-tested construction product
- DIN 71-3 (Safety of toys)
- DIN 53160 (resistant to saliva and perspiration)
- Cobalt-free & oxime-free, FREE from formaldehyde, aromatics, biocides, preservatives
Application recommendation:
- Before every maintenance treatment, prior dry and damp cleaning with OLI-NATURA wood soapis recommended. Allow the surface to dry completely.
- Shake the container well before use.
Small surfaces (furniture)
- White pad or soak a cotton cloth with maintenance oil and work it into the wood.
- Within 10 minutes, remove the wet oil with a dry cotton cloth/oil-absorbing cloth and polish. No excess oil may remain.
- Protect from water during the curing period and do not clean with a damp cloth.
Large surfaces (floors):
- Apply maintenance oil evenly in a thin coat using a sprayer or floor mop. Apply more oil to dry areas.
- Within 10 minutes, work the wet oil in with a Super Hand Pad in white or beige under the pad holder for telescopic handle
- . Alternatively, you can use a single-disc machine. Polish until the surface appears even. Super Hand Pad Finally, polish the surface with a oil-absorbing cloth in white or
- Protect from water during the curing period and do not clean with a damp cloth.
. No excess oil may remain on the surface. Drying:
Allow the surface to dry for at least 12 hours before use. Overnight is preferable. Do not wipe with a damp cloth during the first few days. Coverage:
Depending on the application and the absorbency of the substrate, 10-20 g/m² per coat. NOTE:
Coverage depends on the type of wood and the absorbency of the substrate. Excess material on non-absorbent areas delays drying, as do low temperatures and/or excessively high humidity and/or excessively high wood moisture content.
The maintenance oil is recommended for refreshing oxidatively oiled surfaces. Please do not use it on UV-oiled finished parquet, as the maintenance oil requires an "open-pore system". If in doubt, test on a concealed area. NOTE ON THE RISK OF SPONTANEOUS COMBUSTION:
The product is not subject to labeling requirements. The mixture is not classified as hazardous within the meaning of Regulation (EC) No. 1272/2008. It does not need to be labeled with GHS hazard pictograms or signal words and is not classified as dangerous goods.
Safety instructions
Oil-soaked rags/pads can self-ignite due to heat accumulation! Therefore, clean them immediately after use or store them under water. Keep out of reach of children.
P102 Keep out of reach of children
Wie viel OLI NATURA® Holzpflegeöl brauche ich für meine Fläche?
Je nach Gebindegröße reicht OLI NATURA® Holzpflegeöl bei einem dünnen Pflegeauftrag für folgende Flächen:
- 250 ml: ca. 12,5–25 m²
- 1 Liter: ca. 50–100 m²
Die Angaben beziehen sich auf die Pflege bereits geölter Holzoberflächen.
Hinweis: Alle Reichweiten sind Richtwerte. Die tatsächliche Reichweite hängt von Holzart, Endschliff, Saugfähigkeit des Holzes und Verarbeitungsweise ab. Bei der Nachpflege beeinflusst zusätzlich der Pflegezustand der Oberfläche den Verbrauch.
Wann sollte geöltes Holz nachgeölt werden?
Wenn die Wasserabweisung nachlässt, der Holzfarbton verblasst oder die Oberfläche trocken und stumpf wirkt. Feste Pflegeintervalle gibt es nicht – entscheidend sind Nutzung, Beanspruchung und Pflegezustand.
Was ist der Unterschied zwischen Holzpflegeöl und Refresher?
OLI NATURA® Holzpflegeöl imprägniert nach und vertieft den natürlichen Holzfarbton. OLI NATURA® Refresher pflegt optisch neutral – besonders bei hellen, weiß geölten und rohholzoptischen Oberflächen.
Ist das Holzpflegeöl für jedes geölte Parkett geeignet?
Nein. Es eignet sich für oxidativ geölte Böden, auch werkseitig geölte Oberflächen nach Eignungsprüfung. Nicht auf UV-geöltem Fertigparkett verwenden.
Kann ich einzelne Treppenstufen oder Möbelstellen nachölen?
Ja. Beanspruchte Stellen an Treppen, Holztischen und Möbeln lassen sich gezielt nachimprägnieren. Wegen der möglichen Farbvertiefung vorab eine Probefläche anlegen.
Muss ich das Holz vor der Nachpflege schleifen?
Nein, normalerweise genügt eine gründliche Reinigung mit OLI NATURA® Holzseife. Bei starken Verschmutzungen kann eine Intensivreinigung mit OLI NATURA® PreOilCelaner erforderlich sein. Vor dem Ölen vollständig trocknen lassen.
Wie trage ich Holzpflegeöl auf Möbel und Treppen auf?
Dünn mit einem weißen Polierpad oder Baumwolltuch auftragen und einarbeiten. Überschüssiges Öl innerhalb von 10 Minuten vollständig abnehmen und trocken auspolieren.
Warum bleibt die Oberfläche nach dem Ölen klebrig?
Meist wurde zu viel Öl aufgetragen oder der Überschuss nicht vollständig entfernt. Deshalb innerhalb von 10 Minuten trocken auspolieren. Es darf kein Ölfilm zurückbleiben.
Wann darf ich Böden, Treppen und Möbel wieder benutzen?
Nach mindestens 12 Stunden, besser über Nacht, vorsichtig nutzbar. Nach 2–3 Tagen vollständig durchgehärtet. Bis dahin vor Wasser und starker Beanspruchung schützen.
Any questions? - We’re happy to help!
Frequently bought together
*applies to deliveries within Germany. Delivery times for other countries can be found in the shipping conditions